owners manual Seat Alhambra

all ratings: 0 average rating: 5

Advice 1 Tyre valve remover ●Shake the bottle of sealant ››› Fig. 190 10 200-250 kPa) ››› . Do not leave it running f e than 8 minutes ››› well. or mor . 2 Sticker indicating maximum speed “max. 80 km/h” or “max. 50 mph” ●Screw the inflator tube ››› Fig. 190 3 into●Switch off the compressor. the sealant bottle in a clockwise direction. 3 Filler tube with cap ●If it fails to reach a pressure of between The seal on the mouth of the bottle pierces 2.0 and 2.5 bar (29-36 psi / 200-250 kPa), 4 Air compressor automatically. unscrew the inflator tube from the tyre valve. 5 ON/OFF switch ●Remove the lid from the filling tube ●Move the vehicle some 10 metres forwards 1) 6 Air bleed screw ››› Fig. 190 3 and insert the open end of the or backwards so that the sealant is evenly 1) tube into the tyre valve. 7 Tyre pressure monitoring distributed in the tyre interior. ●Keep the bottle mouth facing down and 8 Tube for inflating tyres ● Securely screw the compressor tyre inflator empty all the contents into the tyre. tube into the tyre valve again and repeat the 9 12 volt connector ●R ve the empty bottle from the valve. emo inflation process. 10 Bottle of sealant ●Screw in the valve insert again with the aid ●If the indicated pressure can still not be 11 Spare insert for valve of the extractor ››› Fig. 190 1 . reached, the tyre is too badly damaged. The The valve insert remover 1 has a gap at the tyre cannot be sealed with the tyre mobility lower end for a valve insert. The valve insert Inflating the tyre system. Do not continue driving. You should can only be screwed or unscrewed in this obtain professional assistance ››› . ●Screw the tyre inflator tube ››› Fig. 190 8 way. This also applies to its replacement part ●Disconnect the air compressor and unscrew of the air compressor into the tyre valve. 11 . the inflator tube from the tyre valve. ●Check whether the air bleed screw ●If a pressure between 2.0 and 2.5 bar ››› Fig. 190 6 is tightened. (29-36 psi / 200-250 kPa) is reached, then ●Start the engine and leave it running in Seal and inflate a tyre continue driving at 80 km/h (50 mph) maxi- neutral. mum. Sealing a tyre ●Attach the connector ››› Fig. 190 9 to one ●After 10 minutes, check the pressure again ● of the vehicle's 12 volt sockets ››› page 119. Unscrew the tyre valve cap. › ›› page 253. ●Switch on the air compressor with the ●Use the enclosed extractor ››› Fig. 190 1 ON/OFF switch ››› Fig. 190 5 . to unscrew the valve insert. Place it on a WARNING clean surface. ● Keep the air compressor running until it When inflating the tyre, the air compressor reaches 2.0 to 2.5 bar (29-36 psi / and the inflator tube may become hot. 1) An inflator tube may also be included. 252

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders