Alfa Romeo 33 owners manual page 206

text version of content this owner's manual page from owners manual to the vehicle Alfa Romeo 33, year of production 1983 - 1995:

FRONT AND REAR BRAKES Tighten to the prescribed torque b. syringe in order to suck the 3. Loosen and remove bolt@ liquid of brake clutch tank. two new nuts securing brake connecting thePanhard rod@ to b. AS piping is removed, remember master cylinder to servobrake. body and loosen the equalizer to plug up the ends in order to securing bolt @. (T): Tightening torque avoid foreign matter from en- tering. Brake master cylinder nuts to servobrake . To remove pipes, loosen unions BENDITALIA on both ends. . hoses, 12+ 15N-m To removeunscrew (1.2+ 1.5kgmm unions collectingpipes-to hoses 8.68 + 10.85ft4b) and remove them. Then, discon- nect hose on the other side. ATE c. At the end of installation on car, 21 + 28 N-m both front and rear flexible (2.1 + 2.9kg.m cables must not result to be 15.2 + 21 ft4b) kink. For their check, take as reference the writing with the relevant manufacturer mark c. Pipes must be connected to master cylinder and tightened tolocated on end of pipes, or the light coloured band (for front the indicative prescribed torque. cables) located along pipe itself. @ : Tightening torque d. Having completed installation of Unions securing pipes to brake 1 Unions 5 Bolt piping, fill up brake fluid reser- 2 Fork 6 Bolt master cylinder voir to proper level and bleed 3 Spring 7 screws 8-10 N-m the brakes (Refer to: Brake 4 Panhard rod (0.8 + 1 kgmm System Bleeding). 5.78 + 7.23ft.lb) 4. LowerPanhard bar in order to Tightening torques easy spring@ withdrawing from d: Fill reservoir up to properlevel Hose unions of brake hydraulic pin 0, and from rubber ring@ using only specified fluid (ATE system located on rod itself. Remove spring “S” orAGIP Fl Brake Fluid IO+ 15 N-m by withdrawing Super ED, or IP Auto Fluid FR). it fromequaliz- (1 + 1.5kgmm er 4 7.23 + 10.85 ft-lb) 0 5. If necessary, remove bolt@ 2. Bleed brake system (Refer to: and equaliter. Brake System Bleeding) and, if Pipe unions of brake hydraulic required, also clutch system (Refer system to: Group 12 Subgroup Hydraulic Control - Hydraulic 8+10 N-m System (O-S+ 1 kg-m Bleeding). 5.78 + 7.23 ft.lb) HYDRAULIC 1 Spring 4 Equalizer SYSTEM PIPING 2 Ring 5 Bolt 3 Pin BRAKE PRESSURE REGULATOR VALVE CHECKS AND INSPECTIONS Thoroughly check all brake system REMOVAL piping (pipes and hoses) making sure CAUTION: 1. Unscrew the three unions 1 of they are not out of shape or cracked 0 Do not disassemble components of the brake pressure regulator pipes, and that outer surfaces of pipes do the brake pressure regulator. taking care to close, by means of not show any evidence of oxidation. caps, the two feeding pipes of brake Replace parts that are not flawless. pressureregulator,in order to REMOVAL AND prevent tank emptying. INSTALLATION 2. Remove from body, the brake INSTALLATION 1. Reinstall to body the brake pressure regulator valve by unscrew- pressure regulator valve by tightening ing the two securing screws@ and CAUTION: bolts to the prescribed torque: (1.5 + 2.4kg.m) removing fork @ from contro15 + 24N.m l a. In case of removal or reinstal- spring 0. (10.85 + 17.35ft.lb) and (if pre- lation of brake pipings, use a May 1983 22-8

owners manual Alfa Romeo 33

owners manual Alfa Romeo 33 - year of production: 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995 - Alfa Romeo 33 owners manual EN