owners manual Mercedes GLE

all ratings: 0 average rating: 5

Features 353 button on the rear-view mirror. When doing Programming so, vary the distance between remotecontrol Programmingbuttons Aandtherear-viewmirror. Pay attention to the "Important safety notes"The required distance between remote con- (Y page 352). trol Aandtheintegratedgaragedooropener depends on the garage door drive system. Several attempts might be necessary. You should test every position for at least 25secondsbeforetrying another position. Synchronizing the rolling code Pay attention to the "Important safety notes" (Y page 352). If the garage door system uses a rolling code,features you will also have to synchronize the garage door system with the integrated garage door openerintherear-viewmirror.Todothisyouwilland Garage door remote control A is not includedneedtousetheprogrammingbuttononthedoor with the integrated garage door opener.drive control panel. The programming button maybepositionedindifferentplacesdepending XTurntheSmartKeytoposition2intheignitiononthemanufacturer.Itisusuallylocatedonthe lock (Y page 145). door drive unit on the garage ceiling.Stowage XSelectoneofbuttons;to?tousetocon- Familiarize yourself with the garage door drive trol the garage door drive. operating instructions, e.g. under "Program- XTostartprogrammingmode:pressand mingofadditionalremotecontrols",beforecar- holdoneofbuttons;to?ontheintegratedrying out the following steps. garage door opener. Yourvehiclemustbewithinreachofthegarage The garage door opener is now in program-door or gate opener drive. Make sure that nei- ming mode. After a short time, indicatorther your vehicle nor any persons/objects are lamp :lights up yellow. present within the sweep of the door or gate. Indicator lamp : lights up yellow as soon asXTurntheSmartKeytoposition2intheignition button ;, =or?isprogrammedforthe lock (Y page 145). first time. If the selected button has alreadyXGetoutofthevehicle. beenprogrammed,indicatorlamp:willonlyXPresstheprogrammingbuttononthedoor light up yellow after ten seconds havedrive unit. elapsed. Usually, you now have 30 seconds to initiate XReleasebutton;,=or?.Indicator the next step. lamp :flashes yellow. XGetintothevehicle. XToprogramtheremotecontrol:point XPresspreviously programmed button ;, = garage door remote control A towards but-or ?ontheintegrated garage door opener tons;to?ontherear-viewmirroratadis-multiple times until the door closes. tance of 2 to 8 in (5 to 20 cm). Therolling code synchronization is then com- XPressandholdbuttonBonremotecontrol plete. Auntilindicator lamp : lights up green. Whenindicator lamp : lights up green: pro-Notesonprogrammingtheremotecon- grammingis finished. trol Whenindicator lamp : flashes green: pro-Canadianradiofrequencylawsrequirea"break" grammingwassuccessful.Thenextstepisto(or interruption) of the transmission signals synchronize the rolling code ( Ypage353). afterbroadcastingforafewseconds.Therefore, XReleasebutton BonremotecontrolAforthese signals may not last long enough for the the garage door drive system. integratedgaragedooropener.Thesignalisnot If indicator lamp : lights up red: repeat therecognized during programming. Comparable programing procedure for the corresponding Z

All pages in one PDF file!

How to get the code?
It's very simple! Just pay through a secure PayPal payment.
It will take no longer than a few minutes.
You will receive the code immediately after payment.
The code will be displayed on the screen and will be sent to you by e-mail address.

---

:

How many PDF files you want to download:
1 PDF file $4,00 USD 3 PDF files $8,00 USD 5 PDF files $12,00 USD

- I agree to the terms of service

Site map |
Privacy |
DMCA |
Terms of service
contact e-mail: contact @ man4car.com
All marks are the property of their respective holders